The drying process of building diaphragm plate increases the performance

The drying process of building diaphragm plate increases the performance

The drying process of building diaphragm plate increases the performance

The drying process of building diaphragm plate increases the performance

In construction industry, building film face plywood is one of a kind of very important material, and popular with everyone, its use has not only the performance of environmental performance, and good protection performance, the main role of building film face plywood is actually has the very good protection effect, so the production building film face plywood, the process and performance have to do?Let's see.To get more news about commercial plywood, you can visit boosterplywood.com official website.
First of all, let's talk about building film face plywood in the drying process, in fact, building film face plywood this process is used in kiln drying technology, this technology is to use the kiln drying was carried out on the plate, because this method does not use too many tools, so it is the cost savings, at the time of drying, is on the material internal moisture to dry, and then use steam evaporated, and then, before processing, on drying, plate plate internal moisture control more uniform, in this case, will avoid cracking or deformation phenomenon in a plate.So this method is the main role is increasing the performance of building film face plywood, construction template itself is actually has the very good performance, beautiful and practical, through the strict production process, the surface of the template which will be more smooth and flat, the advantages of using building film face plywood will not cause any pollution to the environment.
Everyone in daily life, may not too can often see building film face plywood, but everyone know generally seen in site, the use of building film face plywood, for the performance of the workers are taking to protect. Common foundation has independent foundation and strip foundation, the price of building template of independent foundation and strip foundation is not much different.

1.Stepped based architecture template: every step templates composed of four sides fight nail, one of the two sides or side size is equal with the corresponding steps, the other two sides should length is longer than the steps of the corresponding side length about 150 an 150 mm, with equal height.Four sides with wood block Mosaic box, up the steps of the template with two sides of the surface under a makeup lengthen, in order to put on the lower level template, the lower steps around the mould plate to set a brace and flat.One end of the diagonal brace and the other end is fastened to the anchor post.The sides of the upper step template shall be provided with inclined support and peaceful support. One end of the oblique support and peaceful support shall be nailed to the wooden frame of the upper step side panel, and the other end shall be nailed to the top of the wooden frame of the lower step side panel.
2.Cup-shaped foundation building template: the structure of cup-shaped foundation template needs to install the cup-shaped core module at the position of the cup mouth, and the coup-shaped core model is fastened with the car bars on both sides.So that they can sit on the top step template.Where there is a slope on the top of the lower step, the coupe shall be fastened on both sides of the upper step formwork, and the bottom of the end of the coupe shall be fastened with a supporting wood so as to be used on the template of the lower step.When there is a foundation pit wall near by, the foundation pit wall can be attached with cushion wood, with inclined support and flat support side plate.
3.Strip foundation building template installation steps: the bottom of the channel pop-up base line - side panel on the touchline vertical erect, water leveling ruler correction and brace peace side panel top horizontal nail up - based two end side plate correction and pull line one by one, made in accordance with the general line in the middle of the side panel.When the height of the side plate is greater than that of the foundation step, the side plate can be spanked by the height of the step in the inner side of the side plate, and round nails are nailed on the line every 2m intervals as the sign of pouring concrete.In order to prevent the formwork from deforming during pouring, the top of the side plate is nailed with the head wood at a certain distance.
4.Strip foundation with floor girder: strip foundation with floor girder, the car bar is arranged at the top of the side board, and the side board is suspended on the car bar with inclined support and hanging wood.A long spacer plate is laid on both sides of the foundation groove, and the two ends of the coupler bar are put on it, and a wooden wedge is added to adjust the elevation of the side plate.


freeamfva jack

119 Blog posts

Comments